Wax Carver
 Wax Carver Hylin US $5.00 
|
 Wax Carver PK4 US $5.00
|
 Wax Carver PK2 US $5.00
|
 Wax Carver PK1 US $5.00
|
Some folks like to joke that the best tool for any job is a bigger hammer. A woodworker's joinery mallet, with its massive square head, fits that description, but there's more to it than that.
A well-designed mallet is light enough to control comfortably but heavy enough to deliver useful power without requiring a wild, roundhouse swing. A mallet also offers a broader striking surface than a hammer, and one that is tailored to the nature of the work. While a carver's slender mallet allows pinpoint control and a much lighter touch, the joinery mallets broad, flat striking surface is ideal for other tasks that require more force and less flexibility.
A square-headed mallet excels at driving chisels to chop joinery, especially when cutting across the grain for dovetails or mortises. It's also great for project assembly and other tasks that require a firm rap or two. Another great thing is that a mallet is easy to make.
Start with a blank of splinter-resistant hardwood such as hard maple. A block about 3 in. sq. by 41⁄2 in. to 5 in. long will make a mallet head that is massive and heavy enough to deliver a blow with great force when needed. You can glue up such a block if you don't have 12/4 stock available, but be aware that the glue joint might fail eventually.
A through-mortise in the mallet head provides an attachment point for the handle. To make it, find and mark the center in the top of the blank. Then, using a drill press or a hand-held drill with a spade bit bore a 3⁄4-in. diameter hole through the blank, top to bottom. Use a rat-tail (round tapering) rasp to elongate the hole on the top of the mallet head by 1⁄16 in. to 1⁄8 in. toward the end grain in each direction. The wider opening should taper down about halfway through the mortise. If you don't have a rasp or file, a 1⁄2-in. dowel and some course sandpaper will do a decent job.
Next, mark the striking surfaces of the mallet for cutting at a slight angle from top to bottom. An angled surface will strike the butt of a tool handle more squarely because the mallet itself typically will be angled slightly upward when the blow lands. Cutting the ends is simplest on the bandsaw. Plane or sand away the sawmarks. It's also a good idea to bevel the edges and corners of the block to prevent splintering.
The handle also should be of a sturdy, straight-grained hardwood such as maple, birch, hickory, or oak. Start with a 12-in. length that is 3⁄4 in. thick by 11⁄4 in. wide.
Begin by marking the layout for the tenon that will connect the handle to the head. At one end, mark a centerline to bisect the width of the piece. Use this line to lay out a 3/4-in. square. Next, mark out a shoulder line 31/2 in. from the end of the piece and then cut away the waste on the bandsaw to create the square tenon. The extra 1⁄2 in. of tenon length will allow the tenon to protrude from the mallet head so it can be trimmed flush after glue-up.
Making a square tenon round is relatively easy if you follow the steps shown in the photos on p. 34. (Of course, if you have a lathe, you can turn the entire handle. Once you have a true cylinder, use a scraper, sandpaper, or a smooth file to finish shaping the tenon, testing and fitting until it goes into the mortise. The handle should fit snugly, but you shouldn't have to strike it to drive the tenon all the way into the mortise.
Next, use a bandsaw or a handsaw to cut a sawkerf about 21⁄2 in. deep down through the center of the tenon and perpendicular to the 11⁄4-in. dimension. This kerf will hold the wedge that secures the handle to the mallet head. You want the wedge parallel to the striking surfaces. If it were parallel to the long grain, it could split the mallet head. Before assembling the mallet, shape the handle for a comfortable grip.
To keep a solid connection between mallet and handle, I drive a glued wedge into the kerf in the top of the handle. This expands the handle against the walls of the mortise and tightens the fit. Make the wedge 2 in. to 3 in. long, no thicker than 1⁄4 in. to 3⁄8 in.
To assemble the mallet, put a little glue on the inside of the mortise and push the handle into place, making sure it's oriented correctly to the striking surfaces. Next, apply some glue to the wedge and hammer it into the sawkerf. When the glue dries, saw off the wedge and the excess length of handle, then chisel or plane the top smooth.
Wipe on a little Watco or linseed oil for an optional finish. Avoid wax-too much will make the grip slippery.
David Leryco is a professional carpenter and woodworking craftsman. For more information on woodworking plans and woodworking projects, visit http://hotwoodworkingplans.com/guides
Whats On My YouTube Today?
Carving a Head out of Wax: Facial Features : Carve the Ear Canal on a Wax Sculpture
Here Are A Few Items From Amazon You Might Be Interested In.
 SE Pick Set, 12Pc Stainless Steel Wax Carvers Sale Price: $13.69  Eligible for free shipping!Availability: Usually ships in 24 hours  |
 DENTAL PICK wax carver SPATULA probe = DP-30 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL PICK wax carver SPATULA probe = DP-31 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 5pc SPATULA & CHISEL - set wax carver - probes - DENTAL PICKS Sale Price: $6.43 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
|
SE Pick Set, 12Pc List Price: Sale Price: $5.81 You save: $8.44 (59%) Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL PICK wax carver SPATULA probe = DP-02 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL DIGITAL WAX CARVER WITH 2 PENCIL + 6 TIPS S500N Sale Price: $286.35 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL PICK wax carver SPATULA probe = DP-08 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL PICK wax carver SPATULA probe = DP-03 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
 DENTAL PICK wax carver SPATULA probe = DP-01 Sale Price: $3.99 Eligible for free shipping!Availability: Usually ships in 1-2 business days |
Items recently purchased on this site:
Thanks for visiting!
Tags: jewelry, crafts, wax carver 5